View Profile: rlouie - Subaru XV Forum : Subaru XV Crosstrek Forums

7 Visitor Messages

  1. View Conversation
    Hey, did you get a throttle happy tune on your xv? If so wondering how its held up. Cheers
  2. View Conversation
    Hello Richard, hope you remember me I am Fred in New Mexico. From what I've read in the forum; your Canadian XV comes with HID headlights? I wondered if by chance others have asked you about that and if you knew what the cost of them might be? Or if not a dealer you recommend to me to contact to see about getting a pair for myself.
    Hope all is well your way, all ok here. Thank you!
  3. View Conversation
    Richard I juat got your messages here, thank you! I am kinda a bit computer challenged, but got them, thanks!
  4. Did you remember to fill the inside of the angled adapter? Also, when you get the Dynamat, I would put a bit on the high side of the adapter to cut down on any vibration since the material is pretty thin.
  5. View Conversation
    I did a rough install of one of the MM6501 door speakers in my lt ft door. with out cutting the bit of platic from the door panel and it went together just fine, back on the door. I guess i am still confused about the trimming of the plastic in the door panel???? I NEED to do it, or not? Thanks for all your help!
    I havre Dynamat coming this week.I'll keep you posted.
  6. View Conversation
    I did a rough install of one of the MM6501 dorr speakers in my lt ft door. with out cutting the bit of platic from the door panel and it went together just fine, back on the door. I guess i am still confused about the trimming of the plastic in the door panel???? I NEED to do it, or not? Thanks for all your help!
    I havre Dynamat coming this week.I'll keep you posted.
  7. View Conversation
    Update on my speakers/installation.
    I did order the adapter plates you suggested, cable adapters, and did order Dynamat and Dynamat tape. Got everything today except for the Dynamat panels. Did a check out mount of the right hand front door speaker, using the angled adapter you suggested. I re-installed the door panel, and didn't cut the small In some speaker installation pics online I saw one gentleman cut a portion of the door card needs to be cut down in order not to interfere with the speaker suspension. (The rear speakers will not have this issue) {at this post } http://www.scoobymods.com/showthread...ek-14244.html?

    Did you have to cut the above mentioned car door panel for the speaker suspension to be free? I didn't take a close look down in the door panel but was able to install the panel with out cutting the bottom part of the door panel. It lookes like the speaker is ok...? Thank you again!
Showing Visitor Messages 1 to 7 of 7
About rlouie

Basic Information


About rlouie
Location
Vancouver, BC, Canada

Signature


Richard

2013 XV Sports trim (Canadian) - Deep Cherry - CVT

Statistics


Total Posts
Total Posts
5,603
Posts Per Day
3.55
Visitor Messages
Total Messages
7
Most Recent Message
01-29-2017 03:44 AM
General Information
Last Activity
Today 04:35 AM
Join Date
01-03-2013
Referrals
0

7 Friends

  1. coletrain coletrain is offline

    Senior Member

    coletrain
  2. CSSM

    CSSM is offline

    Super Moderator

    CSSM
  3. gavoon

    gavoon is offline

    Super Moderator

    gavoon
  4. jamesxv

    jamesxv is offline

    Super Moderator

    jamesxv
  5. MartinTheOrange MartinTheOrange is offline

    Senior Member

    MartinTheOrange
  6. Ruckus Ruckus is offline

    Senior Member

    Ruckus
  7. Talesonelves Talesonelves is offline

    Senior Member

    Talesonelves
Showing Friends 1 to 7 of 7
Powered by vBadvanced CMPS v4.1.2